BMW M52B28 / M52TUB28 Engine

  1. Specifications
  2. Overview, problems
  3. Performance tuning

M52B28 / M52TUB28 Specs

Manufacturer  Munich Plant
Also called BMW M52
Production 1995-2001
Cylinder block alloy Nikasil-coated aluminum
Configuration Straight-6
Valvetrain DOHC
4 valves per cylinder
Piston stroke, mm (inch) 84 (3.3)
Cylinder bore, mm (inch) 84 (3.3)
Compression ratio 10.2
Displacement 2793 cc (170.4 cu in)
Power output 142 kW (193 HP) at 5,300 rpm
142 kW (193 HP) at 5,500 rpm (TU)
Torque output 280 Nm (210 lb·ft) at 3,950 rpm
280 Nm (210 lb·ft) at 3,500 rpm (TU)
Redline 6,500 rpm
HP per liter 69.1
Fuel type Gasoline
ECU Siemens MS41.0
Siemens MS42.0 (TU)
Weight, kg (lbs) ~170 (375)
~180 (397)
Fuel consumption, L/100 km (mpg)

for E36 328i
11.6 (18.1)
7.0 (35.1)

8.5 (26.1)
Turbocharger   Naturally aspirated
Oil consumption, L/1000 km
(qt. per miles)
up to 1.0
(1 qt. per 750 miles)
Recommended engine oil 0W-30
Engine oil capacity, L (qt.) 6.5 (6.9)
Oil change interval, km (miles)  7,000-10,000
Normal engine operating temperature, °C (F) ~95 (203)
Engine lifespan, km (miles)
-Official information

 ~250 (155)
Tuning, HP
-Max HP
-No life span loss


The engine is installed in BMW 328i E36
BMW 328i E46
BMW 528i E39
BMW 728i E38
Land Rover Defender

BMW M52B28 engine reliability, problems and repair

The eldest representative of M52 family was firstly introduced in 1995. The series of engines also includes M52B20, M52B24, M52B25 and S52B32. This motor was used on E36, E39 models as well as on E38 728i autos produced by major Bavarian automaker. Cylinder block was made of aluminum with the exception of autos which were exported to the USA. M52B28 engine is square: Bore x Stroke – 84×84 mm. Cylinders diameter is the same as in M52B25. Crankshaft has increased stroke, piston compression height is 31.82 mm while connecting rods are 135 mm long. The size of injectors is 250 cc.

M52TUB28 modified version was produced in 1998. It was equipped with cast iron sleeves located in the cylinder block. Double-Vanos engine included new connecting rods and pistons as well as renewed and improved cooling system and electronic throttle body. Specifications of M52TUB28 camshaft are the following: duration – 244/288 deg, lift – 9 mm.

This motor was mainly used on BMW autos with 28i index.

In 2000 successor from new M54 series was introduced. M54B30 engine replaced its predecessor in 2001 and production of was stopped.

BMW M52B28 engine modifications and differences

1. M52B28 (1995 – 2000) is a basic engine modification. Specifications are as follows: compression ratio – 10.2, power – 193 HP at 5,300 rpm, 280 Nm of torque at 3,950 rpm.

2. M52TUB28 (1998 – 2001) Double-Vanos engine on both shafts. It is also equipped with cast iron sleeves and other camshafts (duration – 244/228 deg, lift – 9 mm). Specifications are as follows: compression ratio – 10.2, power – 193 HP at 5,500 rpm, 280 Nm of torque at 3,500 rpm.

BMW M52B28 disadvantages and problems

Disadvantages of 2.8-liter engine are the same as its related M52B25 has. HERE you can find detailed information on reliability of the given engine.

BMW M52B28 engine tuning

M52B28 Stroker 3.0. M50 Manifold. N/A

The easiest way to increase the level of power is to install M50B25 intake manifold as well as cold air intake. At the same time you need to upgrade camshaft and tune ECU. S52B32 camshaft will be the best bet for this purpose. Such kit will guarantee from 240 to 250 HP which is perfect for a city ride and will not cost you a fortune.

There is another alternative to turn your engine into 3-liter M52B30. You need to purchase M54B30 crankshaft to implement this project. Standard pistons should be milled down to 1.6 mm. The rest of bearings should be left stock. M50B25 intake manifold is recommended for improvement of HP characteristics.

M52B28 Turbo. Supercharger

The easiest way is to buy and install Garrett GT35 turbo kit using M52B28 stock internals. After Megasquirt tuning is completed M52B28 Turbo will perform 400 HP when the boost is 10 psi/0.7 bar. It will be followed with a perfect acceleration. Such kind of engine will be the best bet for your everyday drive. It will also show high level of reliability.

BMW M52B28 stock bearings are able to handle with 14 psi/1 bar pressure. Sometimes this rate can be a bit higher. If the HP rate is higher than 450-500, stock pistons should be replaced by forged pistons with 8.5 compression ratio.

If you are a true fan of superchargers, you will certainly benefit from ESS TS2 supercharger kit which is produced on base of Lysholm supercharger. Such systems make it possible to upgrade your engine up to 300 HP and more without replacing stock pistons.


1 Star2 Stars3 Stars4 Stars5 Stars (13 votes, average: 4.31 out of 5)

Related pages

nissan sentra specificationssr20det performance upgradestoyota aurion reliability5vz-fe specstoyota corona t170infiniti qx70 tuninge46 upgrades2004 lexus is300 horsepower325i bmw 2006 specstoyota supra ttbmw 318is specsbmw series 5 e39is300 turbo install2006 bmw 330 specsbmw x3 engines2006 bmw m3 horsepowersr20 turbo specstoyota caldina 2006 review1998 toyota celica gt specs2000 hp turbos54b32 engine for sale2008 bmw 528xi horsepowerrb25det mods2010 toyota matrix specsnissan murano 2009 specsnissan fairlady modifiedbmw s50 motorinfiniti q70 5.6toyota supra torquee90 330i turbobmw x3 motor oil2az fe oil filterbmw m44 engine330xi 2006 specshorsepower in bmw 328itoyota corolla e110335i torque1998 bmw 528i motorbmw m3 e91350z vq35debmw m3 wikitoyota yaris nzej20g turboscion xa dimensions1996 bmw 540i2001 toyota corolla engine sizem5 bmw specsinfiniti fx35 tuningnissan s13.5bmw f10 550i specsm6 bmw horsepowersubaru problems foresterlexus 2jzreview bmw 528ie39 m5 performance partstoyota d4d diesel engine problemsscion xb tuningnissan xterra reliability ratingsbmw 2l twin turbocobb n54lexus sc300 2jznissan murano tuning325i 2004 bmw specsrx300 oil changebmw 335i weightbmw engine e46toyota vista reviewbmw 7 series e66toyota avensis diesel engine1uzfe tuningtoyota corolla ae100 modifiedbmw 328i e46 specs